Description
MOXA Universal Controller ioLogik E1213 Ethernet Switch
The ioLogik E1200 Series supports the most often-used protocols for retrieving I/O data, making it capable of handling a wide variety of applications. Most IT engineers use SNMP or RESTful API protocols, but OT engineers are more familiar with OT-based protocols, such as Modbus and EtherNet/IP. Moxa's Smart I/O makes it possible for both IT and OT engineers to conveniently retrieve data from the same I/O device. The ioLogik E1200 Series speaks six different protocols, including Modbus TCP, EtherNet/IP, and Moxa AOPC for OT engineers, as well as SNMP, RESTful API, and Moxa MXIO library for IT engineers. The ioLogik E1200 retrieves I/O data and converts the data to any of these protocols at the same time, allowing you to get your applications connected easily and effortlessly.
Daisy-Chained Ethernet I/O Connection
This industrial Ethernet remote I/O comes with two switched Ethernet ports to allow for the free flow of information downstream to another local Ethernet device, or upstream to a control server via expandable daisy-chained Ethernet I/O arrays. Applications such as factory automation, security and surveillance systems, and tunneled connections can make use of daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with multidrop as the configuration most typically used in fieldbus solutions. The daisy-chain capabilities supported by ioLogik Ethernet remote I/O units not only increase the expandability and installation possibilities for your remote I/O applications, but also lower overall costs by reducing the need for separate Ethernet switches. Daisy-chaining devices in this way will also reduce overall labor and cabling expenses.
- User-definable Modbus TCP Slave addressing
- Supports RESTful API for IIoT applications
- Supports EtherNet/IP Adapter
- 2-port Ethernet switch for daisy-chain topologies
- Saves time and wiring costs with peer-to-peer communications
- Active communication with MX-AOPC UA Server
- Supports SNMP v1/v2c
- Easy mass deployment and configuration with ioSearch utility
- Friendly configuration via web browser
- Simplifies I/O management with MXIO library for Windows or Linux
- Class I Division 2, ATEX Zone 2 certification
- Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments
Input/Output Interface
Digital Input Channels
4
Configurable DIO Channels (by jumper)
4
Analog Input Channels
4
Isolation
3k VDC or 2k Vrms
Buttons
Reset button
Digital Inputs
Connector
Screw-fastened Euroblock terminal
Sensor Type
Dry contact
Wet contact (NPN or PNP)
I/O Mode
DI or event counter
Dry Contact
On: short to GND
Off: open
Wet Contact (DI to COM)
On: 10 to 30 VDC
Off: 0 to 3 VDC
Counter Frequency
250 Hz
Digital Filtering Time Interval
Software configurable
Points per COM
4 channels
Digital Outputs
Connector
Screw-fastened Euroblock terminal
I/O Type
Sink
I/O Mode
DO or pulse output
Current Rating
200 mA per channel
Pulse Output Frequency
500 Hz (max.)
Over-Current Protection
2.6 A per channel @ 25°C
Over-Temperature Shutdown
175°C (typical), 150°C (min.)
Over-Voltage Protection
35 VDC
Analog Inputs
Connector
Screw-fastened Euroblock terminal
I/O Mode
Voltage/Current
I/O Type
Differential
Resolution
16 bits
Input Range
0 to 10 VDC
0 to 20 mA
4 to 20 mA
4 to 20 mA (with burn-out detection)
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
Sampling Rate
12 samples/sec per module (shared between up to 4 channels)
Built-in Resistor for Current Input
120 ohms
Input Impedance
10 mega-ohms (min.)
Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector)
2, 1 MAC address (Ethernet bypass)
Magnetic Isolation Protection
1.5 kV (built-in)
Ethernet Software Features
Configuration Options
Web Console (HTTP), Windows Utility (ioSearch), MCC Tool
Industrial Protocols
Modbus TCP Server (Slave), Moxa AOPC (Active Tag), MXIO Library, EtherNet/IP Adapter
Management
RESTful API, SNMPv1/v2c, SNMPv1 Trap, HTTP, DHCP Client, BOOTP, IPv4, TCP/IP, UDP
MIB
Device Settings MIB
Security
Access control list
Security Functions
Authentication
Local database
LED Interface
LED Indicators
Power, Ready, Port 1, Port 2
Modbus TCP
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
View AllClose
Additional Information
Stock Available Onehunga: |
0 |
Stock Available Wellington: |
0 |
Stock Available St Lukes: |
0 |
Stock Available Supplier: |
0 |
